Products

Eine Beschreibung zu den Kategorien eingeben!

Sivag product catalogue

Calpeda product catalogue

Zenit product catalogue

Volute casing pumps NC

HoriNC-aggrzontal single-stage volute casing pumps with bearing bracket. Nominal duty points and main dimensions in accordance with ISO 2858 – EN 22858. Single-stage volute casing pumps of type “NC” are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids.

Features

  • DIN 24256
  • ISO 2858
  • EN 22858
  • Maximum nominal pressure: 16 bar (PN 16)
  • Temperature: up to 260°C

Materials:

  • Volute casing pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special material combinations are produced on request.
  • Shaft sealing alternative with mechanical seal or stuffing box. The materials and the execution of the mechanical seal and the packing in accordance to the pumped liquid.

Technical Characteristics:NC-aggr

  • Capacity: up to 1100 m³/h
  • Discharge Head: up to 158 m W.S.
  • Connections: from DN 32 to DN 300
  • Motor rotation speed: 1450 min-1 and 2900 min-1

General Performance Curve:

Kenn-NC

Close coupled pumps NCB

NCBClose coupled horizontal single-stage volute casing pumps with IEC-norm electric motor. Single-stage volute casing pumps of type “NCB” are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids.

Features:

  • Maximum nominal pressure: 16 bar
  • Temperature: up to 180°C

Materials:

  • Volute casing pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special material combinations are produced on request.
  • Shaft sealing alternative with mechanical seal or stuffing box. The materials and the execution of the mechanical seal and the packing in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to  500 m³/h
  • Discharge Head: up to 158 m W.S.
  • Connections: DN 32 to DN 200
  • Motor rotation speed: 1450 min-1 and 2900 min-1

General Performance Curve:

Kenn-NC

Selfpriming centrifugal pumps S

S40Self-priming centrifugal pumps with open impeller are used for pumping liquids containing solids up to 80 mm diameter and for abrasive liquids. The special design makes the “S” series a quick self-priming pump.

Features:

  • Maximum nominal pressure: 16 bar
  • Self-priming up to  8-9 m W.S.

Materials:

  • Self-priming pumps are made of stainless steel 1.4408 (AISI 316) and cast iron. Special materials are produced on request.
  • Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:S85

  • Capacity: up to 1500 m³/h
  • Discharge Head: up to 70 m W.S.
  • Connections: from DN 40 to DN 300

Performances:

Kenn-S-en

Internal gear pumps R

RThe internal gear pumps of type “R” are positive displacement rotary pumps. The capacity is directly proportinal to the rotation speed. This pump is available as bare shaft pump with bearing bracket.

 

 

Features:

  • Maximum nominal pressure: 16 bar
  • Temperature: -60°C to +300°C

Materials:

  • Internal gear pumps are made of stainless steel 1.4408 (AISI 316), cast iron EN-GJL-250 and nodular cast iron EN-GJS-400. Special materials are produced on request.
  • Shaft sealing alternative with mechanical seal, stuffing box or magnetic drive. The materials and the execution of the mechanical seal, packing or magnetic drive in accordance to the liquid.R-R

Technical Characteristics:

  • Capacity: up to 350 m³/h
  • Viscosity: up to 100.000 mm²/s (cSt)
  • Connections: from DN40 to DN250

Performances:

Kenn-R-en

Lobe pumps B

BLobe pumps of series “B” are positive displacement rotary pumps. The capacity is directly proportional to the rotation speed. Two synchronously driven rotors are rotating in a casing. This construction provides a very gentle pumping of fluids.

Features:

  • Maximum working pressure: 10 (20) bar
  • Temperature: up to 180°C
  • Certification 3-A possible
  • Certification EHEDG possible
  • CIP / SIP

Materials:B-aggr

  • All hydraulic parts are made of stainless steel AISI 316. The gear box is made in cast iron EN-GJL-250. Special alloys and surface hardenings available on request.
  • Shaft sealing alternative with mechanical seal, stuffing box or special lip seal. The materials and the execution of the mechanical seal, packing or lip seal in accordance to the liquid.

Performances:

Kenn-B-en

Stainless steel centrifugal pumps 3S

3SHorizontal single-stage volute casing pumps in stainless steel with dimensions and performances acc. EN 733. The “3S”-series is a close coupled execution with standard IEC-norm electric motor. These pumps are used for pumping clean and low contaminated liquids (also used for various chemicals).

Features:

  • Maximum nominal pressure: 10 bar
  • Temperature: -20°C to +120°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4301 (AISI 304) and 1.4571 (AISI 316).
  • Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:3S ohne Motor

  • Capacity: up to 240 m³/h
  • Discharge Head: up to 90 m W.S.
  • Connections from DN 32 to DN 100
  • Motor rotation speed: 1450 min-1 and 2900 min-1

General Performance Curve-  2900 min-1:

Kenn-3-2p

General Performance Curve – 1450 min-1:

Kenn-3-4p

Stainless steel centrifugal pumps 3M

3MHorizontal single-stage volute casing pumps in stainless steel with dimensions and performances acc. EN 733. The “3M”-series is a close coupled execution with electric motor with extended shaft. These pumps are used for pumping clean and low contaminated liquids (also used for various chemicals).

Features:

  • Maximum nominal pressure: 10 bar
  • Temperature: -20°C to +120°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4301 (AISI 304) and 1.4571 (AISI 316).
  • Shaft sealing with mechanical seal. Materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:3M-Schnitt

  • Capacity: up to 240 m³/h
  • Discharge Head: up to 90 m W.S.
  • Connections from DN 32 to DN 100
  • Motor rotation speed: 1450 min-1 and 2900 min-1

General performance Curve – 2900 min-1

Kenn-3-2p

General Performance Curve – 1450 min-1

Kenn-3-4p

Air operated double diaphragm pumps DDA

DDAThe air operated double diaphragm pumps of type “DDA” are used for pumping a variety of different liquids (mainly chemicals), without abrasive, coarse or extended solids. These pumps can be installed submerged in the pumped liquid. The DDA-pumps are self-priming. And they can be used for thin and viscose fluids. This series contains special pumps for food industry named “DFA”.

Features

  • Viskosity: up to 50.000 cP
  • Maximum suction head: 6 m
  • Temperature: -10°C to +40°C

Materials:

  • The air operated double diaphragm pumps are made of PP (glass fiber reinforced Polypropylene), PVDF, carbon fiber filled PVDF, Aluminium, stainless steel AISI 316 (AISI 316 polished – FDA).
  • Pump execution and materials, diaphragm and valves in accordance to the pumped liquid.

Technical Characteristics:DFA2

  • Capacity: up to 40 m³/h
  • Discharge Head: up to 70 m W.S.
  • Connections: from 1/4″ to 2″

DDA all

Close coupled centrifugal pumps with threaded ports NM, NMD

image_NM-NMD_02Close coupled horizontal single-stage (NM) and double-stage (NMD) centrifugal pumps with electric motor with extended shaft directly connected to the pump. The centrifugal pumps of type “NM” and “NMD” are used for pumping clean and low contaminated liquids without abrasive, coarse or extended solids.

Features:

  • Maximum permissible working pressure: 10 bar (NM), 16 bar (NMD)
  • Temperatures: from -10°C to +90°C

Materials:

  • Centrifugal pumps are mode of cast iron and bronze.
  • Shaft sealing with mechanical seal.Materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_NM-NMD_03

  • Capacity: up to 70 m³/h
  • Discharge Head: up to 115 m W.S.
  • Connections: from 1″ to 2 1/2″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-NM_NMD

Close coupled centrifugal pumps with flanged connections NM, NMS

image_NM-NMS_02Close coupled horizontal single-stage centrifugal pumps with electric motor with extended shaft (NM) and with  IEC-norm motor (NMS). The centrifugal pumps of type  “NM” and “NMS” are used for pumping clean and low contaminated liquids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperature: from -10°C to +90°C

Materials:

  • Centrifugal pumps are made of cast iron and bronze.
  • Shaft sealing alternative with mechanical seal or stuffing box. Materials of mechanical seal and quality of packing in accordance to the pumped liquid.

Technical Characteristics:image_NM-NMS_04

  • Capacity: up to 300 m³/h
  • Discharge Head: up to 95 m W.S.
  • Connections: from DN 32 to DN 125
  • Motor rotation speed: 2900 min-1

General Performance Curve – 2900 min-1:

Kenn-NM

Close coupled centrifugal pumps n= 1450 min-1 NM4, NMS4

image_NM-NMS_02Close coupled horizontal single-stage centrifugal pumps with electric motor with extended shaft (NM4) and with IEC-norm motor (NMS4). The centrifugal pumps of type “NM4” and “NMS4” are used for pumping clean and low contaminated liquids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperature: from -10°C to +90°C

Materials:

  • Centrifugal pumps are made of cast iron and bronze.
  • Shaft sealing alternative with mechanical seal or stuffing box. Materials of mechanical seal and quality of packing in accordance to the pumped liquid.

Technical Characteristics:image_NM-NMS_04

  • Capacity: up to 460 m³/h
  • Discharge Head: up to 65 m W.S.
  • Connections: from 1″ to DN 200
  • Motor rotation speed: 1450 min-1

General Performance Curve – 1450 min-1:

Kenn-NM4

End-Suction Centrifugal Pumps N

image_N-N4_03Horizontal single-stage centrifugal pumps with bearing bracket and free shaft end. Nominal duty points and main dimensions in accordance with EN733. The centrifugal pumps of type “N”  are used for pumping clean and low contaminated liquids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperature: from -10°C to +90°C

Materials:

  • Centrifugal pumps are made of cast iron and bronze.
  • Shaft image_N-N4_02sealing alternative with mechanical seal or stuffing box. Materials of mechanical seal and quality of packing in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 300 m³/h
  • Discharge Head: up to 95 m W.S.
  • Connections: from DN 32 to DN 125
  • Motor rotation speed: 2900 min-1

General Performance Curve – 2900 min-1:

Kenn-N

End-Suction Centrifugal Pumps n= 1450 min-1 N4

image_N-N4_03Horizontal single-stage centrifugal pumps with bearing bracket and free shaft end. Nominal duty points and main dimensions in accordance with EN733. The centrifugal pumps of type “N4” are used for pumping clean and low contaminated liquids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperature: from -10°C to +90°C

Materials:

  • Centrifugal pumps are made of cast iron and bronze.
  • Shaft image_N-N4_02sealing alternative with mechanical seal or stuffing box. Materials of mechanical seal and quality of packing in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 460 m³/h
  • Discharge Head: up to 65 m W.S.
  • Connections: from DN 32 to DN 200
  • Motor rotation speed: 1450 min-1

General Performance Curve – 1450 min-1:

Kenn-N4

In-line pumps NR, NR4

image_NR-NR4_02Close coupled, single-stage inline-centrifugal pumps with electric motor with extended shaft directly connected to the pump. Pump casing with suction and delivery connections with the same diameter and on the same axis (inline). The centrifugal pumps of type “NR” and “NR4” are used for pumping clean and low contaminated liquids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperatures: from -10°C to +90°C

Materials:

  • Centrifugal pumps are made of cast iron.
  • shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_NR-NR4_01

  • Capacity: up to 100 m³/h
  • Discharge head: up to 95 m W.S.
  • Connections: from DN 40 to DN 125
  • Motor rotation speed: 1450 min-1 and 2900 min-1

General Performance Curves:

Kenn-NR_NR4

Horizontal multi-stage close coupled pumps MXH 2,4,8,16

image_MXH_02Horizontal, multi-stage close coupled centrifugal pumps in chrome-nickel stainless steel with electric motor with extended shaft,directly connected to the pump. Centrifugal pumps of type “MXH” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 8 bar
  • Temperature: -15°C to +110°C

Materials:

  • Centrifugal pumps are made of stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXH_03

  • Capacity: up to 25 m³/h
  • Discharge Head: up to 70 m W.S.
  • Connections: from 1″ bis 2″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MXH

Horizontal multi-stage close coupled pumps MXHL

image_MXH_02Horizontal, multi-stage close coupled pumps in chrom-nickel-molybdenum stainless steel AISI 316L (1.4404), with electric motor with extended shaft directly connected to the pump.Centrifugal pumps of type “MXHL” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 8 bar
  • Temperature: -15°C to +110°C

Materials:

  • Centrifugal pumps are mode of stainless steel 1.4404 (AISI 316L).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXH_03

  • Capacity: up to 13 m³/h
  • Discharge Head: up to 70 m W.S.
  • Connections: from 1″ to 1 1/2″
  • Motor rotation speed: 2900 min-1

General Performence Curve:

Kenn-MXHL

Horizontal multi-stage close coupled pumps MXH 32,48

image_MXH_04Horizontal multi-stage close coupled centrifugal pumps in chrome-nickel stainless steel with electric motor with extended shaft, directly connected to the pump. Centrifugal pumps of type “MXH” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperature: -15°C to +110°C

Materials:

  • Centrifugal pumps are made of stainess steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXH_05

  • Capacity: up to 66 m³/h
  • Discharge Head: up to 75 m W.S.
  • Connections: from 2″ to DN 80
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MXH32_48

Horizontal multi-stage close coupled pumps MXP

image_MXP_02Horizontal multi-stage close coupled centrifugal pumps in chrome-nickel stainless steel with electric motor with extended shaft, directly connected to the pump. Centrifugal pumps of type “MXP” are used for clean liquids.

Features:

  • Maximum permissible working pressure: 8 bar
  • Temperature: 0°C to +50°C

Materials:

  • Centrifugal pumps are made of stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 7 m³/h
  • Discharge Head: up to 45 m W.S.
  • Connections: 1″
  • Motor rotation speed: 2900 min-1

General Performance Curves:

Kenn-MXP

Horizontal multi-stage close coupled pumps MGP

image_MGP_02Horizontal multi-stage close coupled centrifugal pumps in cast iron with electric motor with extended shaft, directly connected to the pump. Centrifugal pumps of type “MGP” are used for pumping clean liquids.

Features:

  • Maximmum permisseble working pressure: 8 bar
  • Temperature: 0°C to +50°C

Materials:

  • Centrifugal pumps are made of cast iron.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 7 m³/h
  • Discharge Head: up to 45 m W.S.
  • Connections: 1″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MGP

Vertical multi-stage close coupled pumps MXSU

image_MXSU_01Vertical multi-stage close coupled pumps in chrome-nickel stainless steel, with motor shield in brass. Suction connection on the lower casing and delivery connection on the top casing. Motor cooled by the pumped water passing between the motor jacket and the external jacket. Centrifugal pumps of type “MXSU” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperature: up to +35°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with interposed oil chamber. Materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 11 m³/h
  • Discharge Head: up to 65 m W.S.
  • Connections: 1 1/4″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MXSU

Vertical multi-stage close coupled in-line pumps MXV-B

image_MXVB_02Vertical multi-stage close coupled pumps with suction and delivery connections of the same diameter and arranged along the same axis (in-line) with electric motor with extended shaft, directly connected to the pump. Centrifugal pumps of type “MXV-B” are used for pumping clean liquids.

Features:

  • Maximmum permissible working pressure: 16 bar
  • Temperature: -5°C to +90°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXVB_01

  • Capacity: up to 25 m³/h
  • Discharge Head: up to 120 m W.S.
  • Connections: from 1″ to 2″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MXVB

Vertical multi-stage in-line pumps MXV

image_MXV_01Vertical multi-stage pumps with suction and delivery connections of the same diameter and arranged along the same axis (in-line) with IEC-norm electric motor. Centrifugal pumps of type “MXV” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 25 bar
  • Temperature: -15°C to +110°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXV_02

  • Capacity: up to 60 m³/h
  • Discharge Head: up to 245 m W.S.
  • Connections: from 1″ to 1 1/2″ and from DN 25 to DN 80
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MXV

Vertical multi-stage in-line pumps n= 1450 min-1 MXV4

image_MXV_01Vertical multi-stage pumps with suction and delivery connections of the same diameter and arranged along the same axis (in-line) with IEC-norm electric motor. Centrifugal pumps of type “MXV4” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 25 bar
  • Temperature: -15°C to +110°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXV_02

  • Capacity: up to 30 m³/h
  • Discharge Head: up to 62 m W.S.
  • Connections: from 1″ to 1 1/2″ and from DN 25 to DN 80
  • Motor rotation speed: 1450 min-1

General Performance Curve:

Kenn-MXV4

Vertical multi-stage in-line pumps MXVL

image_MXV_03Vertical multi-stage pumps with suction and delivery connections of the same diameter and arranged along the same axis (in-line) with IEC-norm electric motor. Centrifugal pumps of type “MXVL” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 25 bar
  • Temperature: -15°C to +110°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4404 (AISI 316L).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXV_01

  • Capacity: up to 60 m³/h
  • Discharge Head: up to 245 m W.S.
  • Connections: from 1″ to 1 1/2″ and from DN 25 to DN 80
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MXVL

Vertical multi-stage in-line pumps n= 1450 min-1 MXVL4

image_MXV_03Vertical multi-stage pumps with suction and delivery connections of the same diameter and arranged along the same axis (in-line) with IEC-norm electric motor. Centrifugal pumps of type “MXVL4” are used for pumping clean liquids.

Features:

  • Maximum permissible working pressure: 25 bar
  • Temperature: -15°C to +110°C

Materials:

  • Centrifugal pumps are made in stainless steel 1.4404 (AISI 316L).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXV_01

  • Capacity: up to 30 m³/h
  • Discharge Head: up to 62 m W.S.
  • Connections: from 1″ to 1 1/2″ and from DN 25 to DN 80
  • Motor rotation speed: 1450 min-1

General Performance Curve:

Kenn-MXVL4

Self-drainging whirlpool pumps SPA

Self-drainiimage_SPA_01ng single-stage pumps with motor insulated from pumped water. Constructed with high quality, corrosionproof plastic materials, with stainless steel diffuser. Compact design (158 mm wide).

Features:

  • Maximum permissible working pressure: 2,5 bar
  • Temperature: up to +60°C

Materials:

  • Centrifugal pumps are onstructed with high quality, corrosionproof plastic materials (ABS and PPO-GF30, NORYL).
  • Shaft sealing with mechanical seal.

Technical Characteristics:

  • Capacity: up to 18 m³/h
  • Discharge Head: up to 17 m W.S.
  • Connections: 2 1/4″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-SPA

Self-priming swimming pool pumps MPC

image_MPC_03Self-priming swimming pool pumps with built-in strainer and motor insulated from pumped water. The pump is made with high quality plastic materials, corrosion and sand erosion resistant. With stainless steel diffuser.

Features:

  • Maximmum permissible working pressure: 2,5 bar
  • Temperature: up to +60°C

Materials:

  • Centrifugal pumps are made with high quality plastic materials (PPO-GF30, NORYL).
  • Shaft sealing with mechanical seal.

Technical Characteristics:

  • Capacity: up to 40 m³/h
  • Discharge head: up to 18 m W.S.
  • Connections: 1 1/2″ and 2″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MPC

Self-priming centrifugal pumps with built in strainer NMP

image_NMP_02Close-coupled self-priming centrifugal pumps with built-in strainer. Mainly for water circulation in swimming pool filtration systems. For clean or slightly dirty water with solids in suspension.

Features:

  • Maximmum permissible working pressure: 6 bar
  • Temperature: up to +60°C

Materials:

  • Centrifugal pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal.

Technical Characteristics:image_NMP_03

  • Capacity: up to 110 m³/h
  • Discharge Head: up to 37 m W.S.
  • Connections: 2″ to 3″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-NMP

Self-priming centrifugal pumps A

image_A_02Close-coupled centrifugal pumps with open impeller. The built-in backflow preventer avoids reverse siphoning when the pump is stopped and assumes automatic re-priming at the next start. For clean or slightly dirty liquids, also with solids up to 15 mm.

Features:

  • Maximum permissible working pressure: 6 bar
  • Temperature: from -10°C to +90°C
  • Solids: up to 15 mm

Materials:

  • Centrifugal pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_A_03

  • Capacity: up to 67 m³/h
  • Discharge Head: up to 35 m W.S.
  • Connections: 1 1/2″ to 3″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-A

Centrifugal pumps with open impeller C

image_C_02 Close-coupled centrifugal pumps with open impeller. Free-flow impeller for type C 16/1E. Electric motor with extended shaft, directly connected to the pump. Centrifugal pumps of type “C” are used for pumping clean and moderately dirty liquids or emulsions.

Features:

  • Maximum permissible working pressure: 6 bar
  • Temperature: from -10°C to +90°C
  • Solids: up to 4 mm

Materials:

  • Centrifugal pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_C_03

  • Capacity: up to 15 m³/h
  • Discharge Head: up to 22 m W.S.
  • Connections: 1/2″ to 1 1/2″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-C

Peripheral pump CT 61

image_CT_03Close-coupled peripheral pump (regenerative pump) with turbine impeller. Compact, patented construction with single-piece motor casing and pump-side wall. Protected against water entering the motor from outside. Peripheral pump type CT 61 is used for pumping clean liquids without abrasives, without suspended solids.

Features:

  • Total suction lift: up to 7 m
  • Temperature: up to +60°C

Materials:

  • Peripheral pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_CT_04

  • Capacity: max. 2,3 m³/h
  • Discharge Head: max. 41 m W.S.
  • Connections: 1″
  • Motor rotation speed: 2900 min-1

Performance Curve:

Kenn-CT61

Peripheral pump CT 60

image_CT_05Close-coupled peripheral pump (regenerative pump) with turbine impeller. Compact, patented construction with single-piece motor casing and pump-side wall. Protected against water entering the motor from outside. Peripheral pump type CT 60 is used for pumping clean liquids without abrasives, without suspended solids.

Features:

  • Total suction lift: up to 7 m
  • Temperature: up to +60°C

Materials:

  • Peripheral pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: max. 2,3 m³/h
  • Discharge Head: max. 41 m W.S.
  • Connections: 1″
  • Motor rotation speed: 2900 min-1

Performance Curve:

Kenn-CT60

Peripheral pumps T, TP

image_T-TP_02Close-coupled peripheral pumps (regenerative pump) with turbine impeller, with electric motor with extended shaft directly connected to the pump. Peripheral pumps of type “T” and “TP”are used for pumping clean liquids without abrasives, without suspended solids.

Features:

  • Total suction lift: up to 7 m
  • Temperature: from -10°C to +60°C

Materials:

  • Peripheral pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_T-TP_03

  • Capacity: max. 6 m³/h
  • Discharge Head: max. 170 m W.S.
  • Connections: from 3/4″ to 1 1/4″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-T

Self-priming liquid ring pumps CA

image_CA_02Close-coupled self-priming liquid ring pumps with star impeller with electric motor with extended shaft directly connected to the pump. Liquid ring pumps of Type “CA” are used for pumping clean liquids without  abrasives, without suspended solids.

Features:

  • Total suction lift: up to 9 m
  • Temperature: from -10 to +90°C

Materials:

  • Liquid ring pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_CA_03

  • Capacity: max. 2,5 m³/h
  • Discharge Head: max. 55 m W.S.
  • Connections: from 1/2″ to 1″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-CA

Self-priming jet pumps NGL

image_NGL_02Close-coupled self-priming shallow-well pump with built-in ejector, with electric motor with extended shaft directly connected to the pump. Self-priming jet pumps of type “NGL” are used for pumping clean and low contaminated liquids without abrasives, without suspended solids.

Features:

  • Maximum permissible working pressure: 8 bar
  • Temperature: 0°C to +35°C

Materials:

  • Pumps are made in cast iron.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 5 m³/h
  • Discharge Head: up to 50 m W.S.
  • Connections: 1″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-NGL

Self-priming jet pumps NGX

image_NGX_02Close-coupled self-priming shallow-well pump with built-in ejector, with electric motor with extended shaft directly connected to the pump. Self-priming jet pumps of type “NGX” are used for pumping clean and low contaminated liquids without abrasives, without suspended solids.

Features:

  • Maximum permissible working pressure: 8 bar
  • Temperature: 0°C to +35°C

Materials:

  • Pumps are made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 8 m³/h
  • Discharge Head: up to 60 m W.S.
  • Connections: 1″ to 1 1/4″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-NGX

Self-priming jet pumps NG

image_NG_02Close-coupled self-priming shallow-well pump with built-in ejector, with electric motor with extended shaft directly connected to the pump. Self-priming jet pumps of type “NG” are used for pumping clean and low contaminated liquids without abrasives, without suspended solids.

Features:

  • Maximum permissible working pressure: 10 bar
  • Temperature: 0°C to +40°C

Materials:

  • Pumps are made in cast iron and bronze.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_NG_03

  • Capacity: up to 10 m³/h
  • Discharge Head: up to 95 m W.S.
  • Connections: 1″ to 1 1/2″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-NG

Multi-stage self-priming pumps MXA

image_MXA_02Close-coupled horizontal multi-stage self-priming pump, with electric motor with extended shaft directly connected to the pump. Self-priming pumps of type “MXA” are used for pumping clean and low contaminated liquids without abrasives, without suspended solids.

Features:

  • Maximum permissible working pressure: 8 bar
  • Temperature: 0°C to +35°C

Materials:

  • Pumps are made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 8 m³/h
  • Discharge Head: up to 55 m W.S.
  • Connections: 1″ to 1 1/4″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-MXA

Gear pumps I, IR

image_I-IR_02Close-coupled gear pump (rotary pump). Pump casing with suction and delivery connections with the same diameter and on the same axis (in-line execution).

Features:

  • Viskosity: from 30 mm²/s to 120 mm²/s
  • Temperature: up to 90°C

Materials:

  • The gear pumps are made in cast iron.
  • Shaft sealing with radial shaft seal rings in FPM.

Technical Characteristics:

  • Capacity: 0,6 m³/h
  • Discharge Pressure: up to 5 bar
  • Connection: 1″

Performances:

Kenn-I

Peripheral immersion pump B-VT

image_BVT_01Vertical close-coupled peripheral (regenerative) pump with submerged turbie impeller. Seal-less, reversible. Peripheral pump of type B-VT are used for pumping clean liquids without abrasives, without suspended solids. Submerged deph 170 mm

Features:

  • Viscosity: up to 20 mm²/s
  • Temperature: water up to +90°C, oil up to +150 °C

Materials:

  • Peripheral pumps are made of bronze.
  • Without shaft sealing.

Technical Characteristics:

  • Capacity max. 3 m³/h
  • Discharge Head: max. 50 m W.S.
  • Connections: 3/4″
  • Motor rotation speed: 2900 min-1

Performance Curve:

Kenn-BVT

Vertical submerged pumps VAL, SC

image_VAL-SC_01Vertical column sump pump with motor in dry installation and with pump body submerged in the liquid handled. Without suction line or foot valve.

VAL – free-flow impeller

SC – open impeller

Features:

  • Maximum size of solids: VAL: up to 50 mm, SC: up to 6 mm
  • Temperature: up to +40°C

Materials:

  • Vertical column pumps are made of cast iron.image_VAL-SC_02
  • Without shaft sealing.

Technical Characteristics:

  • Capacity: max. 30 m³/h
  • Dischatge Head: max. 12 m W.S.
  • Connections: 1 1/4″ to 2″
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-VAL_SC

Centrifugal pumps for chemicals TMR, ZMR

ZMR1Close-coupled horizontal single-stage centrifugal pumps with standard IEC-norm electric motor. This centrifugal pumps are used for pumping clean liquids (mainly chemicals) without abrasive, coarse or extended solids. Pumps of type “TMR” are equipped with magnetic drive, and type “ZMR” are equipped with mechanical seal.

Features:

  • Maximum nominal pressure: 8 bar
  • Temperature: -20°C to +100°C

Materials:

  • Centrifugal pumps are made of PP (glass fiber reinforced Polypropylene) or E-CTFE (Ethylene-Chloro TrifluoroPolyetylene carbon fibers filled / PVDF-similar).
  • Shaft sealing is available with mechanical seal or magnetic coupling. Pump execution and materials, mechanical seals and bushings in accordance to the pumped liquid.

Technical Characteristics:TMR1

  • Capacity: up to 55 m³/h
  • Discharge Head: up to 40 m W.S.
  • Connections: from DN 40 to DN 50
  • Motor rotation speed: 2900 min-1

General Performance Curve:

Kenn-ZMR_TMR

Centrifugal pumps for chemicals ZGE

ZGEHorizontal single-stage volute casing pumps, with bearing bracket. Nominal duty points and main dimensions in accordance to EN 22858. Centrifugal pumps of type “ZGE” are used for pumping clean liquids (mainly chemicals) without abrasive, coarse or extended solids.

Features:

  • Maximum nominal pressure: 16 bar
  • Temperature: -40°C to +120°C

Materials:

  • Centrifugal pumps are made of PP (Polypropylene), PE (Polyethylene); PVDF (Polyvinilidene Fluoride) or PVC (Polyvinyl chloride).
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: up to 1700 m³/h
  • Discharge Head: up to 155 m W.S.
  • Connections: from DN 32 to DN 300
  • Motor rotation speed: 1450 min-1 and 2900 min-1

General Performance Curve – 2900 min-1:

Kenn-ZGE-2900

General Performance Curve – 1450 min-1:

Kenn-ZGE-1450

Chemical vertical sump pumps KGK

KGK_400The vertical sump pumps of type “KGK” are used for pumping clean liquids (mainly chemicals) without abrasive, coarse or extended solids. They have column and volute casing submerged, own mechanical support and motor mounted above the liquid to be pumped.

Features:

  • Maximum immersion depth: 4 m
  • Temperature: -10°C to +40°C

Materials:

  • Centrifugal pumps are made of PP (glass fiber reinforced Polypropylene) and PVDF (Polyvinilidene Fluoride).
  • Pump execution and materials and bushings in accordance to the pumped liquid.KGK

Technical Characteristics:

  • Capacity: up to 270 m³/h
  • Discharge Head: up to 85 m W.S.
  • Connections: from DN 25 to DN 100
  • Motor rotation speed: 1450 min-1 and 2900 min-1

General Performance Curve – 2900 min-1:

Kenn-KGK-2900

General Performance Curve – 1450 min-1:

Kenn-KGK-1450

Multi-stage submersible clean water pumps MXS

image_MXS_02Close-coupled multi-stage submersible pump. All parts in contact with the fluid (both internal and external) are in chrome-nickle stainless steel. Hydraulics located below the motor with the motor cooled by the pumped fluid. Safe operation is possible with the motor only partially submerged. The suction strainer prevents the entrance of solids with diameter bigger than 2 mm.

Features:

  • Temperature: up to +35°C
  • Minimum internal diameter of well: 140 mm
  • Maximum immersion depth: 20 m

Materials:

  • Pumps are made of stainless steel 1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_MXS_01

  • Capacity: max. 11 m³/h
  • Discharge Head: max. 115 m
  • Connection: 1 1/4″
  • Motor: 0,45-3,0 kW, 2900 min-1

General Performance Curve:

Kenn-MXS

Peripheral submersible borehole pump SFM 70

image_SFM70_01Submersible borehole pump for 4″ deep wells (DN 100 mm), with turbine impeller. The special plastic and stainless steel hydraulic materials prevent the impeller from locking even after long stationary periods.

Features:

  • Temperature: up to +35°C
  • Minimum internal diameter of well: DN 100
  • Maximum sand quantity into the water: 20 g/m³

Materials:

  • Delivery casing in Nylon PA66 + 30% GF (brass thread inserts), upper plate in Ryton R4, lower plate in stainless steel AISI 304, impeller in brass, shaft,  shell and filter in stainless steel AISI 304.
  • Shaft sealing with mechanical seal, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: max. 2,7 m³/h
  • Discharge Head: max. 65 m
  • Connection: 1″
  • Motor: 0,75 kW, 2900 min-1

Performance Curve:

Kenn-SFM70

Submersible borehole pumps for 4″ and 6″ wells SD

image_SD_02Submersible borehole pumps for 4″ wells (DN 100 mm) and 6″ wells (DN 150 mm) with external jacket in stainless steel AISI 304 and stages in polycarbonate for 4SD pumps and in noryl for 4SDF and 6SDN pumps. Connection: screwed connection ISO 228. Delivery casing with built-in non-return valve.

Features:

  • Temperature: up to +25°C for 4″ motors, up to 30°C for 6″ motors
  • Minimum internal diameter of well: 4SD-pumps: DN 100, 6SD-pumps: DN 150
  • Maximum sand quantity into the water: up to 150 g/m³

Materials:

  • Pumps are made in stainless steel AISI 304.

Technical Characteristics:SD-Familie

  • Capacity: max. 33 m³/h
  • Discharge Head: max. 360 m
  • Connections: 1 1/4″, 2″ and 3″
  • Motor: 0,37-22,0 kW, 2900 min-1

General Performance Curve:

Kenn-SD

Submersible borehole pumps for 6″ and 8″ wells SDX

image_SDX_03Submersible borehole pumps for 6″ wells (DN 150 mm) and 8″ wells (DN 200 mm). Pumps of type “6SDX” and “8SDX” with external jacket and stages in stainless steel AISI 304. Pumps of type “6SDXL” and “8SDXL” with external jacket and stages in stainless steel AISI 316L. Connection: screwed connection ISO 228. Delivery casing with built-in non-return valve.

Features:

  • Temperature: up to +25°C
  • Minimum internal diameter of well: 6SDX-pumps: DN 150, 8SDX-pumps: DN 200
  • Maximum sand quantity into the water: up to 100 g/m³

Materials:

  • Pumps of type “SDX” are made in stainless steel AISI 304 and pumps of type “SDXL” are made in stainless steel AISI 316L.

Technical Characteristics:SDX-Familie

  • Capacity: max. 120 m³/h
  • Discharge Head: max. 700 m
  • Connections: 2 1/2″, 3″ and 5″
  • Motor: 2,2-110,0 kW, 2900 min-1

General Performance Curve:

Kenn-SDX

Submersible borehole pumps for 6″, 8″ and 10″ wells SDS

image_SDS_02Submersible borehole pumps for 6″ wells (DN 150 mm), 8″ wells (DN 200 mm) and 10″ wells (DN 250 mm) with stages in cast iron or bronze on request. Connection: screwed connection ISO 228 for 6SDS, flange with counter-flange for welding for 8SDS and 10SDS. Delivery casing with built-in non-return valve.

Features:

  • Temperature: up to +25°C
  • Minimum internal diameter of well: 6SDS-pumps: DN 150, 8SDS-pumps: DN 200, 10SDS-pumps: DN 250
  • Maximum sand quantity into the water: up to 150 g/m³

Materials:

  • Pumps are made in cast iron. Bronze on request.

Technical Characteristics:SDS-Familie

  • Capacity: max. 350 m³/h
  • Discharge Head: max. 500 m
  • Connections: 3″, 4″, DN 100, DN 125 und DN 175
  • Motor: 5,5-185,0 kW, 2900 min-1

General Performance Curve:

Kenn-SDS

Pumps with vortex impeller DG Blue, DG Blue Pro

DG Blue ProSubmersible pumps series “DG Blue” with set back vortex impeller for pumping all kinds of waste water, sewage and sludge. The vortex impeller grants pumping fluids containging solids up to 50 mm diameter.
 
 

Features:

  • Temperature: up to +40°C
  • Maximum solid size: 50 mm

Materials:

  • Cast iron
  • Seal set comprising of two opposing mechanical seals in silicon carbide and alumina graphite (DG Blue) or rather two opposing silicon carbide mechanical seals (DG Blue Pro) in oil sump, and V-ring in direct contact with the liquid.

Technical characteristics:

  • Capacity: up to 12,6 m³/h
  • Discharge head: up to 15,3 m
  • Connections from G1 1/2″ to 2″ vertical
  • Motor: 0,37 – 1,5 kW, 2900 min-1

Characteristics diagram:

Kenn-DG-Blue

Pumps with vortex impeller DGE

DGESubmersible pumps series “DGE” with set back vortex impeller for pumping all kinds of waste water, sewage and sludge. The vortex impeller grants pumping fluids containging solids up to 50 mm.

Features:

  • Temperature: up to +40°C
  • Maximum solid size: 50 mm

Materials:

  • Cast iron
  • Seal set comprising one silicon carbide mechanical seal and one lip seal.

Technical characteristics:

  • Capacity up to max. 11,6 l/s
  • Discharge head up to 15,7 m
  • Connections from 2″ vertical, DN50 horizontal
  • Motor: 0,37 – 1,5 kW, 2900 min-1

Pumps with vortex impeller DGO

DGOSubmersible pumps series “DGO” with set back vortex impeller for pumping all kinds of waste water, sewage and sludge. The vortex impeller grants pumping fluids containing solids up to 80 mm.

Features:

  • Temperature: up to +40°C
  • Maximum solid size: 80 mm

Materials:

  • Cast iron
  • Seal set comprising one silicon carbide mechanical seal and one graphite alumina mechanical seal, installed opposing with oil lubrication.

Technical characteristics:

  • Capacity up to 19 l/s
  • Discharge head up to 17,3 m
  • Connections 1 1/2″ – 2 1/2″ vertical
  • 2″ – DN 50 horizontal
    DN65 – DN80 horizontal

  • Motor: 0,37 – 1,5 kW, 2900 min-1 u. 1450 min-1

Pumps with vortex impeller DGN

DGNSubmersible pumps series “DGN” with set back vortex impeller for puming all kinds of waste water, sewage and sludge. The vortex impeller grants pumping fluids containing solids up to 150 mm diameter.
 
 

Features:

  • Temperature: up to +40°C
  • Maximum solid size: 150 mm

Materials:

  • Cast iron
  • Seal set comprising two opposing silicon carbide mechanical seals in inspectable oil sump.

Technical characteristics:

  • Capacity up to 46,4 l/s
  • Discharge head up to 22,3 m
  • Connections: 2 1/2″ vertical
  • DN65 – DN 150 horizontal

  • Motor: 1,1 – 4,1 kW, 2900 min-1 u. 1450 min-1

Pumps with vortex impeller DGP

DGPSubmersible pumps series “DGP” with set back vortex impeller for puming all kinds of waste water, sewage and sludge. The vortex impeller grants pumping fluids containing solids up to 102 mm diameter.

Features:

  • Temperature: up to +40°C
  • Maximum solid size: 102 mm

Materials:

  • Cast iron
  • Seal set comprising two silicon carbide mechanical seals installed in series in inspectable oil sump and one opposed graphitealumina lip seal lubricated by the motor oil.

Technical characteristics:

  • Capacity up to 101,4 l/s
  • Discharge head up to 17,9 m
  • Connections: DN80 – DN 125 horizontal
  • Motor: 4,6 – 16,4 kW, 2900 min-1 u. 1450 min-1

Pumps with multi-channel impeller DR Blue, DR Blue Pro

DR Blue ProSubmersible pumps series “DR Blue” with open multi-channel impeller for pumping clean and waste water, with solids contaminated sewage and sludge. This kind of impeller grants pumping fluids containing solids up to 15 mm diameter.

Features:

  • Temperature: up to +40°C
  • Maximum solid size: 15 mm

Materials:

  • Cast iron
  • Seal set considered with two opposing mechanical seals in silicon carbide and alumina graphite in oil sump (DR Blue) or rather with two opposing silicon carbide mechanical seals in oil sump (DR Blue Pro).

Technical characteristics:

  • Capacity up to 11,5 l/s/li>
  • Discharge head up to 17 m
  • Connections: G1 1/4″ bis 2″ vertical
  • Motor: 0,3 – 1,5 kW, 2900 min-1

General performance curve:

Kenn-DR-Blue

Pumps with multi-channel impeller DRE

DRESubmersible pumps series “DRE” with open multi-channel impeller for pumping clean and waste water with solids contaminated sewage and sludge. This kind of impeller grants puming fluids containging solids up to 15 mm.

Features:

  • Temperature: up to +40°C
  • Maximum solid size: 15 mm

Materials:

  • Cast iron
  • Seal set comprising one silicon carbide mechanical seal and one lip seal.

Technical characteristics:

  • Capacity up to 12,6 l/s/li>
  • Discharge head up to 18 m
  • Connections: G1 1/4″ bis 2″ vertical
  • G 2″ – DN 50 horizontal

  • Motor: 0,37 – 1,5 kW, 2900 min-1

 

Pumps with multi-channel impeller DRO

DROSubermsible pumps series “DRO” with open multi-channel impeller for pumping clean and waste water, with solids contaminated sewage and sludge. This kind of impeller grants pumping fluids containing solids up to 120 mm diameter.

Features:

  • Temperature up to +40°C
  • Maximum solid size: 15 mm

Materials:

  • Cast iron
  • Seal set comprising one silicon carbide mechanical seal and one graphite alumina mechanical seal, installed opposing with oil lubrication.

Technical characteristics:

  • Capacity up to 13 l/s/li>
  • Discharge head up to 18,4 m
  • Connections: G1 1/4″ – 2″ vertical
  • G 2″ – DN 50 horizontal

  • Motor: 0,37 – 1,5 kW, 2900 min-1

Pumps with multi-channel impeller DRN

DRNSubermersible pumps series “DRN” with open multi-channel impeller for pumping clean and waste water, with solids contaminated sewage and sludge. This kind of impeller grants pumping fluids containing solids up to 100 mm.

Features:

  • Temperature up to +40°C
  • Maximum solid size: 100 mm

Materials:

  • Cast iron
  • Seal set comprising two opposing silicon carbide mechanical seals in inspectable oil sump.

Technical characteristics:

    • Capacity up to 47,1 l/s/li>
    • Discharge head up to 23,2 m
    • Connections: DN 65 – DN150 horizontal
    • Motor: 1,1 – 4,1 kW, 2900, 1450, 1000 min-1

Pumps with multi-channel impeller DRP

DRPSubmersible pumps series “DRP” with open multi-channel impeller for pumping clean and waste water, with solids contaminated sewage and sludge. This kind of impeller grants pumping fluids containing solids up to 120 mm diameter.

Features:

  • Temperature up to +40°C
  • Maximum solid size: 125 mm

Materialien:

  • Cast iron
  • Seal set comprising two silicon carbide mechanical seals installed in series in inspectable oil sump and one opposed graphitealumina lip seal lubricated by the motor oil.

Technical characteristics:

    • Capacity up to 140,9 l/s/li>
    • Discharge head up to 52,6 m
    • Connections: DN 80 bis DN 150 horizontal
    • Motor: 4,1 – 19,3 kW, 2900, 1450, 1000 min-1

Pumps with grinder system GR

GRNSubermsible pumps series “GR” with open multi-channel impeller and cutting system. This kind of pumps with special impeller and grinder system is used for pumping waste water with long fibers and cutting able solids.
 

Features:

  • Temperature: up to +40°C
  • Max. solid size: – (cutting system)

Materials:GR Blue Pro

  • Cast iron
  • Shaft sealing with mechanical seal. Materials and executions of mechanical seal in accordance to the pumped liquid.

Technical characteristics:

    • Capacity up to 29,6 l/s
    • Discharge head up to 54 m
    • Connections from G 1 1/2″ to DN 100 horizontal
    • Motor: 0,74 – 7,2 kW, 2900, 1450 min-1

General performance curve:

Kenn-GRKenn-GRN4

Pumps with closed single- and dual-channel impeller SM-SB

SBPPumps series “SM” are submersible pumps with closed single impeller and series “SB” with dual-channel impeller. The ideal solution for pumping slurry, soiled water with and without solids, untreated or activated sludges, strained and unstrained biological liquids and rainwater or seepage. The pumps allows ample free passages and high efficiencies.

Features:

  • Temperature up to +40°C
  • max. solid size: 140 mm

Materials:SMP

  • Cast iron
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

Technical characteristics:

    • Capacity: up to 378 l/s
    • Discharge head up to 53,2 m
    • Connections from G 2″ to DN 300 horizontal
    • Motor: 1,5 – 50 kW, 2900, 1450, 960 min-1

General performance curve:

Kenn-SMKenn-SB

Pumps with high head impeller AP

APSSubmersible pumps series “AP” with open multi-channel high head impeller are designed for high delivery heads. They are used for pumping clean and waste water and low contaminated liquids with small solids.

Features:

  • Temperature up to +40°C
  • Maximum solid size: 10 mm

Materials:AP Blue Pro

  • Cast iron
  • Shaft sealing with mechanical seal. Materials and execution of mechanical seal in accordance to the pumped liquid.

Technical characteristics:

    • Capacity: up to 11,8 l/s
    • Discharge head up to 58,3 m
    • Connections from G 1 1/2″ to G 2″, DN 32 horizontal
    • Motor: 0,74 – 10 kW, 2900, min-1

General performance curve:

Kenn-AP kleinKenn-AP gross

Submersible pumps with open single-channel impeller MA

MAFSubmersible pumps series “MA” with open single-channel impeller allows very high performance and ample free passages, often entirely free passages, which reduce the risk of fouling. Units in this family can be used for lifting sewage, for wastewater treatment plants, and for industrial applications in general.
 
 
Features:

  • Temperature: up to +40°C
  • Maximum solid size: up to 100 mm

Materials:MAN

  • Cast iron
  • Standard shaft sealing with two silicon carbide mechanical seals.

Technical characteristics:

    • Capacities up to 53,9 l/s
    • Discharge head up to 30,2 m
    • Connections: G 2 1/2″ vertical, DN 65 to DN 150 horizontal
    • Motor: 0,74 – 4,1 kW, 2900, 1450, 960 min-1

General performance curve:

Kenn-MAI_MANKenn-MAF

Submersible pumps in special alloy DRX-Y-B

DRXSubmersible pumps series “DRX, DRY and DRB” in stainless steel (DRX and DRY) and bronze (DRB) with open multi-channel impeller are used for applications with corrosive and aggressive liquids, and can therefore be used for industrial plants in the chemical and pharmaceutical sector, or with seawater.
 
 
Features:DRY

  • Temperature: up to +40°C
  • Maximum solid size: up to 80 mm

Materials:

  • Stainless steel AISI 316 and Bronze
  • Standard shaft sealing with two silicon carbide mechanical seals (DRX, DRB) and three mechanical seals for DRY pumps (2x silicon carbide, 1x carbon-aluminium oxide)

Technical characteristics:DRB

    • Capacities up to 72,8 l/s
    • Discharge head up to 40,2 m
    • Connections: G 1 1/4″ – 2″ vertical, DN 65 bis DN 100 horizontal
    • Motor: 0,37 – 15 kW, 2900, 1450 min-1

 

Submersible pumps in special alloy DGX, DGB

DGXSubmersible pumps series “DGX and DGB” in stainless steel (DGX) and bronze (DGB) with vortex impeller are used for applications with corrosive and aggressive liquids, and can therefore be used for industrial plants in the chemical and pharmaceutical sector, or with seawater.
 
 
Features:DGB

  • Temperature: up to +40°C
  • Maximum solid size: up to 60 mm

Materials:

  • Stainless steel AISI 316 and Bronze
  • Standard shaft sealing with two silicon carbide mechanical seals

Technical characteristics:

    • Capacities up to 18,4 l/s
    • Discharge head up to 15 m
    • Connections: G 2″ vertical, DN 65 bis DN 80 horizontal
    • Motor: 0,37 – 1,5 kW, 2900, 1450 min-1

 

Submersible pumps Hydro

HYDROSubmersible pumps series “Hydro” with open multi-channel impeller are used for pumping clean and waste water. This pumps are easy to transport because of there handiness and ideal for mobile and flexible applications.
 
Features:hydro-40t

  • Temperature: up to +40°C

 
Materials:

  • Aluminium alloy, cast iron
  • Shaft sealing with two silicon carbide mechanical seals

Technical characteristics:

    • Capacities up to 4.200 l/min
    • Discharge head up to 62 m
    • Connections: G 2 1/2″ to G 6″ vertical
    • Motor: 2,2 – 15 kW, 2900 min-1

 

Submersible drainage pump GM 10

image_GM 10_01Submersible drainage pump constructed with composite polymers developed especially for this product. Pump type GM 10 is a submersible drainage pump with open multi-channel impeller for puming clean and waste water .

Features:

  • Temperature: up to +35°C
  • Maximum solid size: 8 mm

Materials:

  • Pump body made of polymers. Pump shaft in stainless steel 1.4104.
  • Shaft sealing with three lip seals in NBR.

Technical Characteristics:

  • Capacity: max. 12 m³/h
  • Discharge Head: max. 7 m
  • Connection: 1 1/2″
  • Motor: 0,3 kW, 2900 min-1

Performance Curve:

Kenn-GM10

Submersible pumps in stainless steel GXR, GXV

image_GXR_01Submersible pump in stainless steel with vertical delivery port. Motor cooled by the pumped liquid passing between the motor jacket and the external jacket. The submersible pumps of type “GXR” are pumps with open impeller and are used for pumping clean liquids containing solids up to 10 mm grain size. The submersible pumps of type “GXV” are pumps with free-flow impeller (vortex-impeller) and are used for pumping clean and slightly dirty liquids containing solids up to 25 mm grain size.

Features:

  • Temperature: up to +50°C
  • Maximum solid size: GXR: up to 10 mm, GXV: up to 25 mm

Materials:

  • Pumps are made of stainless steel  1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_GXV 25_01

  • Capacity: max. 13 m³/h
  • Discharge Head: max. 12,5 m
  • Connection: 1 1/4″
  • Motor: 0,25-0,45 kW, 2900 min-1

General Performance Curve:

Kenn-GXR_GXV

Submersible pumps in stainless steel GXR 12

image_GXR_12Submersible pump in stainless steel with vertical delivery port. Motor cooled by the pumped liquid passing between the motor jacket and the external jacket. The submersible pumps of type “GXR 12” are pumps with open impeller and are used for pumping clean liquids containing solids up to 12 mm grain size.
 
 

Features:

  • Temperature: up to +50°C
  • Maximum solid size: GXR: up to 10 mm, GXV: up to 25 mm

Materials:

  • Pumps are made of stainless steel  1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal: ceramic/carbon/NBR

Technical Characteristics:

  • Capacity: max. 30 m³/h
  • Discharge Head: max. 19 m
  • Connection: 1 1/2″
  • Motor: 0,45-1,1 kW, 2900 min-1

General Performance Curve:
Kenn_GXR_12

Submersible drainage pump GQR

image_GQR_01Submersible drainage pump with vertical delivery port with open impeller. The submersible pumps of type “GQR” are used for pumping clean liquids containing solids up to 10 mm grain size.

Features:

  • Temperature: up to +35°C
  • Maximum solid size: up to 10 mm

Materials:

  • Pump casing made of cast iron and motor casing in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: max. 30 m³/h
  • Discharge Head: max. 20 m
  • Connection: 1 1/2″
  • Motor: 0,45-1,5 kW, 2900 min-1

General Performance Curve:

Kenn-GQR

Submersible pumps with high power grinder GQG

image_GQG_01Submersible pumps with high power grinder of type “GQG” are used for pumping waste water containing log filamentous, paper and textile materials and organics.

Features:

  • Temperature: up to +35°C
  • Maximum solid size: up to 10 mm

Materials:

  • Pump casing made of cast iron and motor casing in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal: ceramic/carbon/NBR

Technical Characteristics:

  • Capacity: max. 16,8 m³/h
  • Discharge Head: max. 25 m
  • Connection: 1 1/2″
  • Motor: 0,9-1,5 kW, 2900 min-1

General Performance Curve: Kenn_GQG

Submersible sewage and drainage pumps GXC, GXV

image_GX 40_01Submersible drainage pump in stainless steel with vertical delivery port. The submersible pumps of type “GXC” are pumps with two-passage impeller, they are used for pumping clean liquids containing solids up to 35 mm grain size. The submersible pumps of type “GXV” are pumps with free-flow impeller (vortex-impeller), they are used for pumping clean liquids containing solids up to 35 mm grain size.

Features:

  • Temperature: up to +35°C
  • Maximum solid size: up to 35 mm

Materials:

  • Pumps are made in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:

  • Capacity: max. 25 m³/h
  • Discharge Head: max. 13 m
  • Connection: 1 1/2″
  • Motor: 0,55-0,9 kW, 2900 min-1

General Performance Curve:

Kenn-GXC-GXV

Submersible sewage and drainage pumps GQS, GQV

image_GQV_01Submersible drainage pump with free-flow impeller (vortex-impeller). The submersible pumps of type “GQS” are pumps with vertical threaded delivery port 2″. The submersible pumps of type “GQV” are pumps with horizontal flanged and threaded delivery port DN 50 and 2″. They are used for pumping clean liquids containing solids up to 35 mm grain size.

Features:

  • Temperature: up to +35°C
  • Maximum solid size: up to 50 mm

Materials:

  • Pump casing made of cast iron and motor casing in stainless steel 1.4301 (AISI 304).
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_GQS_01

  • Capacity: max. 36 m³/h
  • Discharge Head: max. 15 m
  • Connections: 2″ and DN 50
  • Motor: 0,55-1,5 kW, 2900 min-1

General Performance Curve:

Kenn-GQS_GQV

Submersible sewage and drainage pumps GMC, GMV

image_GM 50_02Submersible drainage pump in cast iron with vertical and horizontal delivery port. The submersible pumps of type “GMC” are pumps with one-passage impeller, they are used for pumping clean liquids containing solids up to 45 mm grain size. The submersible pumps of type “GMV” are pumps with free-flow impeller (vortex-impeller), they are used for pumping clean liquids containing solids up to 50 mm grain size.

Features:

  • Temperature: up to +35°C
  • Maximum solid size: GMC: up to 45 mm, GMV: up to 50 mm

Materials:

  • Pumps are made in cast iron.
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:image_GM 50_01

  • Capacity: max. 48 m³/h
  • Discharge Head: max. 17 m
  • Connection: 2″ and DN 65
  • Motor: 0,75-1,5 kW, 2900 min-1

General Performance Curve:

Kenn-GMC_GMV50

Submersible pumps GM

image_GM_02Series of submersible pumps with high efficiency hydraulics designed to move slurry, sewage and industrial process fluids. This series is available in different materials and hydraulic executions. The range covers a wide field of use with flows up to 2300 m³/h, heads up to 75 m , with maximum solid passage up to 140 mm keeping the risk of blockage to a minimum. Dimensionally designed for heavy demand, even on critical applications.

Features:

  • Temperature: up to +40°C
  • Maximum solid size: up to 140 mm

Materials:

  • Pumps are made in cast iron, stainless steel and bronze.
  • Shaft sealing with double mechanical seal with oil chamber, materials of mechanical seal in accordance to the pumped liquid.

Technical Characteristics:GM-Familie

  • Capacity: max. 2300 m³/h
  • Discharge Head: max. 75 m
  • Connections: DN 40 to DN 300
  • Motor: 1,1-79,5 kW, 2900 min-1, 1450 min-1, 950 min-1, 750 min-1

General Performance Curve:

Kenn-GM

Automatic waste water collecting and lifting station GEO

image_GEO_01Medium-density polyethylene tank, resistant to corrosion, with minimum overall dimensions.image_GEO_02

  • GEO 40: Single tank with 40 liters nominal capacity
  • GEO 230: Single tank with 230 liters nominal capacity
  • GEO 500: Double tank with 500 liters nominal capacity

Details you can find in the download-area at the brochures.

Macerating pumping systems GEOTRIT, GEOCOMP, GEOCLEAN

image_GEOTRIT-GEOCLEAN-GEOCOMP_03This macerating pumping system has been designed to pump away the waste water from a WC, a washbasin, a bidet, a shower, a dishwasher and washing machine.

Details you can find in the download-area at the brochures.

Self-adapt energy saving circulating pumps NCE EA

image_NCE_EA_01Energy saving variable speed circulating pump self-adapt driven by a permanent magnet synchronous motor controlled by on board inverter. EPP insulation shell included.
 

Features:

  • Liquid temperature: +2°C – +95°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 6 bar
  • Storage: -20°C/+70°C
  • Max. Glycol quantity : 40%
  • Minimal suction pressure: 0,3 bar at 50°C, 1,0 bar at 95°C

Technical Characteristics:

  • Capacity: max. 4,2 m³/h
  • Delivery head: max. 6,8 m
  • Connections: G1″ – 2″
  • Installation dimension: 130 bzw. 180 mm
  • Power consumption: 3-56 W

General Performance Curve: Kenn_NCE_EA

Energy saving circulating pumps NCE EI

image_NCE_EI_01Energy saving variable speed circulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 
 

Features:

  • Liquid temperature: +2°C – +95°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 6 bar
  • Storage: -20°C/+70°C
  • Max. Glycol quantity: 40%
  • Minimal suction pressure: 0,3 bar at 50°C, 1,0 bar at 95°C

Technical Characteristics:

  • Capacity: max. 4,2 m³/h
  • Delivery head: max. 6,8 m
  • Connections: G1″ – 2″
  • Installation dimension: 130 bzw. 180 mm
  • Power consumption: 3-56 W

General Performance Curve: Kenn_NCE_EI

Energy saving circulating pumps NCE H

image_NCE_H_01Energy saving variable speed circulating pump driven by a permanent magent synchronous motor controlled by on board inverter.
 

Features:

  • Liquid temperature: +2°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 10 bar
  • Storage: -20°C/+70°C
  • Max. Glycol quantity: 20%
  • Minimal suction pressure: 0,05 bar at 75°C, 0,28 bar at 90°C

Technical Characteristics:

  • Capacity: max. 11 m³/h
  • Delivery head: max. 12 m
  • Connections: G1 1/2,” G2″
  • Installation dimension: 180 mm
  • Power consumption: 10-180 W

General Performance Curve: Kenn_NCE_H_F

Energy saving circulating pumps with flanges NCE H.F

image_NCE_HFEnergy saving variable speed circulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 

Features:

  • Liquid temperature: +2°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 10 bar
  • Storage: -20°C/+70°C
  • Max. Glycol quantity: 20%
  • Minimal suction pressure: 0,05 bar at 75°C, 0,28 bar at 90°C

Technical Characteristics:

  • Capacity: max. 13 m³/h
  • Delivery head: max. 12 m
  • Connections: DN32, DN40, DN50 PN6/10 acc. DIN EN 1092-2
  • Installation dimension: 220, 240 mm
  • Power consumption: 10-180 W

General Performance Curve: Kenn_NCE_H_F

Energy saving circulating pumps with flanges NCE G.F

image_NCE_GFEnergy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 
 

Features:

  • Liquid temperature: -10°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 6/10 bar
  • Storage: -20°C/+70°C
  • Max. glycol quantity: 20%
  • Minimal suction pressure: 0,3 bar at 50°C, 1,0 bar at 95°C

Technical Characteristics:

  • Capacity: max. 75 m³/h
  • Delivery head: max. 17 m
  • Connections: flanges DN50-DN100 acc. PN6/10 DIN EN 1092-2
  • Installation dimension: 280-360 mm
  • Power consumption: 10-1600 W

General Performance Curve: Kenn_NCE_G_F

Energy saving twin circulating pumps NCED G.F

image_NCED_GFEnergy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 

Features:

  • Liquid temperature: -10°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 6/10 bar
  • Storage: -20°C/+70°C
  • Max. glycol quantity: 20%
  • Minimal suction pressure: 0,5 bar at 50°C, 1,4 bar at 95°C

Technical Characteristics:

  • Capacity: max. 75 m³/h
  • Delivery head: max. 17 m
  • Connections: flanges DN 50-DN 100 acc. PN6/10 DIN EN 1092-2
  • Installation dimension: 280-360 mm
  • Power consumption: 10-1600 W

General Performance Curve:Kenn_NCED_G_F

Energy saving circulating pumps with flanges NCE HQ.F

image_NCE_HQFEnergy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 
 

Features:

  • Liquid temperature: +2°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 10 bar
  • Storage: -20°C/+70°C
  • Max. glycol quantity: 20%
  • Minimal suction pressure: 0,05 bar at 75°C, 0,28 bar at 90°C

Technical Characteristics:

  • Capacity: max. 36 m³/h
  • Delivery head: max. 12 m
  • Connections: flanges DN 40, DN 50 acc. PN6/10 DIN EN 1092-2
  • Installation dimension: 250-280 mm
  • Power consumption: 10-560 W

General Performance Curve:Kenn_NCE_HQF

Energy saving twin circulating pumps NCED GQ.F

image_NCED_HQFEnergy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 

Features:

  • Liquid temperature: +2°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 10 bar
  • Storage: -20°C/+70°C
  • Max. glycol quantity: 20%
  • Minimal suction pressure: 0,05 bar at 75°C, 0,28 bar at 90°C

Technical Characteristics:

  • Capacity: max. 36 m³/h
  • Delivery head: max. 12 m
  • Connections: flanges DN40, DN50 acc. PN6/10 DIN EN 1092-2
  • Installation dimension: 250-280 mm
  • Power consumption: 10-560 W

General Performance Curve:Kenn_NCED_HQF

Energy saving circulating pumps for solar systems NCE EL

image_NCE_EL_01Energy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 
 

Features:

  • Liquid temperature: +2°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 10 bar
  • Storage: -20°C/+70°C
  • Max. glycol quantity: 40%
  • Minimal suction pressure: 0,5 bar at 95°C

Technical Characteristics:

  • Capacity: max. 4,2 m³/h
  • Delivery head: max. 6,8 m
  • Connections: G1″, G1 1/2″
  • Installation dimension: 130 and 180 mm
  • Power consumption: 3-56 W

General Performance Curve:Kenn_NCE_EL

Energy saving circulating pumps for sanitary hot water NCE ES

image_NCES_01Energy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 
 

Features:

  • Liquid temperature: +2°C – +95°C
  • Ambient temperature: +2°C – +40°C
  • Max. permissible working pressure: 10 bar
  • Storage: -20°C/+70°C
  • Minimal suction pressure: 0,3 bar at 50°C, 1,0 bar at 95°C

Technical Characteristics:

  • Capacity: max. 3,3 m³/h
  • Delivery head: max. 3,8 m
  • Connections: G1″, G1 1/4″, G1 1/2″
  • Installation dimension: 130 mm
  • Power consumption: 4,5-44 W

General Performance Curve:Kenn_NCE_ES

Energy saving circulating pumps for sanitary hot water NCE PS

image_NCE_PS_01Energy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 
 

Features:

  • Liquid temperature: +2°C – +95°C
  • Ambient temperature: +2°C – +40°C
  • Max. permissible working pressure: 10 bar
  • Storage: -20°C/+70°C
  • Minimal suction pressure: 0,3 bar at 50°C, 1,0 bar at 95°C

Technical Characteristics:

  • Capacity: max. 5 m³/h
  • Delivery head: max. 8,5 m
  • Connections: G1 1/4″, G1 1/2″
  • Installation dimension: 130 mm
  • Power consumption: max. 75 W

General Performance Curve:Kenn_NCE_PS

Energy saving circulating pumps for sanitary hot water NCE GS F

image_NCE_GS_F_01Energy saving variable speed cirulating pump driven by a permanent magnet synchronous motor controlled by on board inverter.
 
 

Features:

  • Liquid temperature: -10°C – +110°C
  • Ambient temperature: 0°C – +40°C
  • Max. permissible working pressure: 6/10 bar
  • Storage: -20°C/+70°C
  • Minimal suction pressure: 0,05 bar at 50°C, 0,8 bar at 80°C, 1,4 bar at 110°C

Technical Characteristics:

  • Capacity: max. 50 m³/h
  • Delivery head: max. 13,5 m
  • Connections: flange DN40, 50, 65 PN 6/10 EN 1092-2
  • Installation dimension: 250-340 mm
  • Power consumption: 20-1100 W

General Performance Curve:Kenn_NCE_GS_F

Pressure Boosting Sets

image_BS_06Pressure Boosting Sets

Fixed speed pump units

Variable speed pump units with frequency converter

Details you can find in the download-area at the brochures.BS-Familie-e

Fire-fighting systems UNI-EN 12845

image_AUE-AUD-AUED_01Fire-fighting systems

Details you can find in the download-area at the brochures.AU-Familie-e

Electronic regulator IDROMAT 3-4

idromatRegulation device for pump control equipped with flow and pressure sensor connected to an electronic system. Inlet and delivery connection ports of the same diameter (1″). Built-in check valve. Pressure gauge 0-10 bar supplied as standard for all models. Automatic reset funktion in IDROMAT 4 for the reset of the system without manual operation.

Applications:

Automatic control of pumps for water supply and increase of network pressure. Control of starting/stopping of the pump when cocks are opened/closed.

For protection of the pump:

  • against dry running
  • against the risk of operation without water at the inlet
  • against operation with closed connection ports

Details you can find in the download-area at the brochures.

Frequency converter I-MAT

imatVariable speed system driven by frequency converter for the motor control in the water supply applications and in the production/distribution of hot/cold water. I-MAT is an integrated control system which, applied to the motor., allows to manage a wide range of applications and operating modes.


Applications:

Frequency converter for automatic pump control suitable for:

  • water supply
  • water transport and distribution
  • production and distribution of hot/cold water
  • water treatment

For protection of the pumps:

  • against dry running
  • against operations with closed connection ports
  • against overcurrent of the motor
  • against overvoltage and undervoltage of the power supply
  • against unbalance or missing supply phases

Details you can find in the download-area at the brochures.

Variable speed system EASYMAT

easymatVariable speed system driven by frequency converter, for the pressure control in domestic and residential plants. The system is connected to the delivery pipe providing for simple installation and better cooling (patented) making the unit more compact and easy to assemble.

Applications:

Automatic frequency inverter control for use on pumps to increase network pressure. The system maintains constant pressure whilst the controlling the pump operation against changing system demand.

For protection of the pumps:

  • against dry running
  • against operations with closed connection ports
  • against overcurrent of the motor
  • against overvoltage and undervoltage of the power supply

Details you can find in the download-area at the brochures.

Variable speed system VARIOMAT 2

image_VARIOMAT_01Variable speed system driven by frequency converter, for the pressure control in domestic and residential plants. The system is connected to the delivery pipe providing for simple installation making the unit more compact and easy to assemble.

Applications:

Automatic frequency inverter control for use on pumps to increase network pressure. The system maintains constant pressure whilst the controlling the pump operation against changing system demand.

For protection of the pumps:

  • against dry running
  • against operations with closed connection ports
  • against overcurrent of the motor
  • against overvoltage and undervoltage of the power supply

Details you can find in the download-area at the brochures.

Control panels QM, QT

schaltschraenkeControl panels

Details you can find in the download-area at the brochures.

 
 
 

Accessories

kit2Accessories

Details you can find in the download-area at the brochures.

Pre-filter in stainless steel

image_PF_02Pre-filter with removable basket, constructed in stainless steel. Loose ring flange connections. Clamp type closing with lever and double adjustment clamp. Inner basket with d= 6 mm holes.

Details you can find in the download-area at the brochures.

Automatic house water systems

HWW-NGLOur house water systems are assembled by us according to the customer’s wishes.
Both upper and lower water pumps are assembled with appropriate equipment.
 

Pressure increase systems with EASYMAT frequency converter

HWW-NGLOur house water systems are assembled by us according to the customer’s wishes.
Both upper and lower water pumps are assembled with appropriate equipment.